VT 510-V2 Connector - Self-adjusting Center Pin

VT 510-V2 Connector - Self-adjusting Center Pin

Your Price: $4.25
In Stock
Part Number:VT_510-V2

Choose Options

Type and Finish
V2-Stainless Smooth Top
V2-Stainless Air Channels
V2-BLACK Smooth Top [+$0.50]
V2-BLACK Air Channels [+$0.50]
V2-30mm-Stainless Smooth Top [+$0.75]
V2-30mm BLACK Smooth Top [+$1.25]
Quantity Pricing
Quantity
Price
  • 2 - 5
  • $4.00
  • 6 - 20
  • $3.75
  • 21 - 49
  • $3.50
  • 50 - 99
  • $3.25
  • 100 - 199
  • $3.00
  • 200+
  • $2.75
The Varitube VT510 V2 is here!  A Bullet Proof Connector:

- NO Need to disassemble for soldering
- NO Threaded insulators to strip
- NO max wire gauge restrictions
- Solder before or after installation

Only 11.5mm long - note you need an additional 2.5mm-3mm to allow movement within the installation

Note -  Properly adjust the T-Nut by loosening or tightening it such that the small pin is flush with the bottom of the slot in the T-Nut on the bottom of the connector ... This allows the top insulator to properly adjust and seat with the Atomizer providing smooth operation.  Pre-loading the spring with an over tightened T-Nut may result in 'ratchety' movement while installing an atomizer ... Adjust the T-Nut prior to soldering!

Ultra low profile shoulder, self-adjusting spring loaded center pin, brass backer nut for solid and secure installation.  

Made of Stainless, Brass, & High Temp insulating material this connector is perfect for box mods and the discerning modder!  

  • The spring carries no electrical load!
  • 22mm with Air Channels
  • 22mm Smooth Top
  • Only 1mm thick landing pad
  • Made of Stainless with High Temp Insulator, and brass - rated for 450F degrees continuous service
  • Assembled connector length - 11.5mm - extends to about 14mm with atomizer installed
  • Body threading - M10x0.5 - 10mm diameter ... about 3/8"
  • Ring Terminal for ground connection included
  • Does NOT need to be disassembled for soldering!!!  Huge productivity gain!  Can be soldered after install as well if desired.  Only adjustment needed is to make sure the bottom T-Nut is not over tightened prior to soldering.
  • Properly adjust the T-Nut by loosening or tightening it such that the small pin is flush with the bottom of the slot in the T-Nut on the bottom of the connector ... This allows the top insulator to properly adjust and seat with the Atomizer providing smooth operation.  Pre-loading the spring with an over tightened T-Nut may result in 'ratchety' movement while installing an atomizer ... Adjust the T-Nut prior to soldering!
Ring Terminals Are Included

Watch the video below from Plumes of Hazard showing how easy to solder it is:

5 Stars
Dr.
Best 510's I have run across, my people, make very nice mods, with Lipos, all using 1S 10,000 mah 100C Lipos, for Unreg. mods that is, and 5,000 mah 100C Lipos for Yihi chip based mods. LOT of current, so I have been buying\making Solid center pin 510's, no spring at all, makes for a bit of a gap between mod and atomizer though. Can be adjusted but, it is a pain. These, I THINK will carry that current, first one is doing so. So, I'm back buying a few more, verifying current capability, and possibility of issues with longevity. When they check out well, and I'm sure they will, I buy many more.
Did you find this helpful?  2 of 3 Found Helpful
Reviewed by: (Verified Buyer)  from Las Vegas. on 4/1/2016
5/5
5 Stars
Great replacement
I got this in order to replace the stupid press-in connector that came loose on my Istick 100W. Works better than the old one. As an aside, to anyone wanting to "fix" their Istick, tapping the existing hole doesn't work so well, and you'll have to remove some material so the ring and nut will fit onto the top cap. Also, the third screw won't go back in because 22m is about 4mm too big and covers the hole. The depth is perfect though. A bit more room than the stock connector.
Did you find this helpful?  1 of 3 Found Helpful
Reviewed by: (Verified Buyer)  from The Windy City. on 2/25/2016
5/5
5 Stars
Good Update
This is a solid improvement over the V1. I can now solder damn near any gauge wire to this 510. It has more throw than the V1. So attys with positive pins meant for hybrid topcaps will sit flush on this 510. Easier to use, Easier to Solder, more options for wire and more throw make this V2 a win. Now hurry up and release those black ones!!
Did you find this helpful?  1 of 3 Found Helpful
Reviewed by: (Verified Buyer)  from Phoenix AZ. on 2/10/2016
5/5
3 Stars
decent
Have been using v1 forever and absolutely love them. Bought six of these v2 to give a try. The concept is good the way it gets soldered can save some space. But the pin tends to hang up and not move freely . Love the design just needs to be improved. I will continue using the v1 for now. update from varitube - we really encourage our customers to fully read the webpage as we do not know how else to get proper instructions to folks. The brass T-Nut needs to be adjusted such that the threaded pin just begins to stick into the slot. If the spring is pre-loaded the pin will hang up. Properly set its very smooth. Several larger mod makers have switched over due to the productivity gains
Did you find this helpful?  1 of 3 Found Helpful
Reviewed by: (Verified Buyer)  from pa. on 1/25/2016
3/5

Recently Viewed Items